| 7.3 Laboratories | ||
|
Faculty of Engineering & Technology (FET) has been established with the objective to meet the growing demand of technically trained engineers. FET provides latest knowledge of different engineering disciplines backed with a support of latest IT systems, general management and vedic views, which would enable an engineer to be a competent technocrat. All the engineering streams have started with a initial intakes of 60 students.
| ||
Chemistry
lab is spacious and comprehensive laboratory and is well equipped with state of
art instruments. It has got all the apparatus, chemicals and accessories for physically
carrying out the experiments as prescribed in the syllabus by the University.
The Laboratory is equipped with various electronic equipments like conductivity
meter, PH Meter, Turbidity meter, Refractrometer, Muffle furnace, Electronic balance,
Flame Photometer. The experiments that are normally carried our by the students
are Determination of PH of a solution; finding out the exact weight of chemical
samples; ignition of the organic sample and to maintain high temperature; determination
of the hardness of water; spectroscopy; determination of the conductivity of the
solutions. |  |
|
|
Electronics and digital laboratory is a fully developed lab in the area of 150 square meter, well equipped with CRO; AD Converters; DA Converters, FET Characteristics amplifier; OP-Amp.Mux & Demux kits and variety of I.Cs.; Function Generators, Half-adder and half subtractor etc. All the experiments as per the University syllabus can be carried out with the help of these equipments.
|  |
|
| The
Institute has set up advance PCB Lab to train the students in the fabrication
of D.C. unregulated Power Supply. The Laboratory is equipped with Shearing Machine;
Etching Machine, Drilling Machine; Soldering equipments We are in the process
of adding U.V.Camera, Transformer winding machine and some more equipments to
make further advance lab.The experiments which are carried out in this Laboratory
are: Art work and printing on simple PCB; Etching and drilling of PCB; Soldering
and fixing of components; Testing of the fabricated power supply
|
 |
|
| This
laboratory is presently having all the necessary instruments relating to measurement
experiments. These are Owen'x Bridge; Maxwell's Bridge; Schering Bridge; Hey's
Bridge; Kelvin's Double Bridge A.C.Voltmeter; A.C.Ammeter; Single Phase Variac,Rheostat,
Choke coil and Potentiometer. The students can carry out main experiments viz:
Measurement of unknown capacitance using Shering Bridge; Measurement of unknown
inductance using Hey's bridge; Measurement of unknown resistance using Kelvin's
Double Bridge;Measurement of the unknown inductance usingOwen's Bridge; Measurement
of unknown inductance using Maxwell's Bridge; Caliberation of A.C.Voltmeter and
A.C.Ammeter; Measurement of Power drawn by Single phase AC circuit using three
ammeters; Measurement of unknown voltage by using potentiometer.
|
||
| This
lab consists of Basic Electrical & Electronics Lab as well as Machine Lab. This
lab is equipped with variety of trainer kits and machines for performing requisite
experiments namely Verification of network theorems; Study of series and parallel
resonance condition by RLC Kit; Study of half wave and full wave rectifier circuit
with and without capacitor filter and determine the ripple factor; Determination
of common base and common emitter characteristics of a transistor; study of various
logic gates (TTL) ; Measurement of power consumed in three phase circuit by two
wattmeter method. The Machine lab section consists Transformer; D.C.Shunt Motor;
D.C.Shunt Generator and the experiments that are carried out in this section are:
Direct load test to find losses and efficiency; Indirect test to draw the equivalent
circuit of the transformer; Regenerative test or back to back test or Sumpner's
test to find efficiency of a tramsformer by using two similar transformers; speed
control of d.c. shut motor via field control, armature control, voltage control;
Swinburn test or no load test to find the efficiency of the motor; To obtain the
magnetization characteristics or open circuit characteristic; To conduct the parallel
operation of d.c. generator; To obtain the load characteristics.
|
||
| The
basic aim of this lab is to train the students for the bread board implementation
of different combinational and sequential circuits. The laboratory is equipped
with Digi Lab Trainer; Bread Board kits; Counter and shift register kits; Flip
Flop Kits. With the help of these kits the students are guided to carry out various
experiments like Implementation of various gates counters and registers using
different integrated chips; Implementation of various gates counters and registers
and code conversion using different integrated chips; Implementation of counters
and shift registers and designing of various counters; Implementation of various
flip flops , set reset (SR) Delay(D), Toggle(T) & JK flip flops.
|
||
| This
lab is having 120 computers in perfect working conditions having speed of 2.66G
Hz and all are Pentium-4. The lab has the facility of server running on Microsoft
windows; Novel network and limux too are installed on the network. The lab has
the facility of four printers which are connected through network. Variety of
software is available to the students to perform practical. Emphasis is given
on the Data base handling; software project development; Programming techniques
in various programming languages.
|
 |
|
| Computer
lab is connected to the internet through tower having very good speed. The students
have their own internet accounts and can access information to their need. Separate
internet lab is for the staff where all academic and other information is accessible
through the net. The internet facility is available to the students for whole
of the day so that they can take advantage even after normal working hours.
|
||
| Communication
laboratory of Electronics & Communication Engineering has various training
kits like DSB/SSB AM Transmitter. DSB/SSB AM Receiver. FM Transmitter/Receiver.
Sampling & Reconstruction. TDM Pulse AM/De-Modulation. TDM Pulse Code Modulator/Receiver.
Delta Adaptive, Delta 7 Delta Sigma M/Demo. Delta Formatting & Carrier Mod
Transmitter, Carrier Demodulation & Delta Reformatting. CROs of 25 MHZ, function
pulse generator of 2 MHZ and AM/FM function pulse generator of 2 MHZ, PAM-PPM-PWM
Modulation and Demodulation etc. are available in the laboratory.
|
 |
|
|
This
lab is equipped with multiple numbers of Microprocessor Kits 8085 & 8086 for
carrying out experiment of Addition, subtraction etc. using assembly language
programming. |
| |
|
There is a separate laboratory for catering to Engineering Physics for B. Tech. first year students. This lab has experimental setup of Fresnel's Biprism, Polarization of Laser Light, Susceptibility measurement by Quinke's method, Hall Effect Setup, Ultrasonic Velocity in liquids. Besides, the physics lab has sufficient experimental equipment to perform experiments according to the prescribed syllabus.
|
...... |
|
|
Mechanical Workshop is broadly divided into five shops such as Carpentry, Foundry, Fitting, Metal Joining and Machine Shop. Lathe machines, Shaper machine, Universal Milling machine, Gas welding and Arc welding set-ups are available in the Mechanical workshop.
|
| |
|
Roorkee
Institute of Technology, boasts of state-of-art Graphics Lab with a seating capacity
of more than 70 students although the standard capacity of each class is
restricted to sixty only as per the AICTE norms.The Graphics Lab as drawing boards
mounted on adjustable drafting stand, and have provision for fixing the mini-drafter
machines for the purpose of preparation of the engineering drawings.
| ||
| 7.3.14 Power Electronics Lab. | ||
|
Well-established lab of power
electronics in ava. All the instruments are or high quality and accuracy.All the
experiments are performed out. In this study practical like V-I characteristics
or SCR, UJT, IGBT etc. are performed and software-based practical are also
performed out.
| ||
|
7.3.15
Power System Lab. | ||
|
Well-established lab. of power system available for the students. All the experiments are performed out about generation, distribution, turns mission etc. All type of experiments about connections is performed out. Study practical about circuit breakers and relays etc.
| ||
|
7.3.16
Electrical Instrumentation Lab. | ||
|
In
this lab practical related to all the instruments use in electrical engineering
are performed out (according to syllabus) like working of whetstone bridge,
transducer, testing of accuracy of instruments.
| ||
|
7.3.17
Telemetry Lab. | ||
|
In telemetry lab experiments
about pulse modulation, pulse amplitude modulation, frequency modulation,
transmitter modulation etc. are performed out.
| ||
| 7.3.18 Electrical Lab. | ||
|
Well-established electrical lab is available. All instrument are of high quality and accuracy installed in the lab. This lab is equipped with variety of trainer kits and machines performing the requisite experiments namely characteristics of diode, half wave rectifier, full wave rectifier, study of single phase transformer, DC generator characteristics, speed control of D.C. Shunt motor, three phase induction motor and energy meter.
| ||
|
7.3.20
Digital Electrical Lab. | ||
|
A fully developed digital
electrical laboratory is available. This lab is equipped with CRO, function
generator, TTL inverters, schmitt trigger, 555 timer, CMOS inverter, Adder/Substractor,
multiplexes/decoders and all accessories for performing the experiment as
prescribed in the syllabus by the university. In addition to this Digital Lab.
Trainer and breadboard kits are also installed.
| ||
|
7.3.21
Instrument Of Measurement Lab. | ||
|
In this lab all necessary instruments and accessories are installed for performing measuring experiments. These are LCR bridge distortion factors meter, transistor tester, Owen’s Bridge, Kelvin’s Double Bridge, A.C. Voltmeter, A.C. ammeter, single phase variac, rheostat, choke coil and Potentiometer, CRO different types of transducers (PT-100 trans, J-type trans-K-type trans & presser trans). The students carry out main experiments viz:- Calibration of AC voltmeter and are ammeter, measurement of phase difference and frequency of a sinusoidal AC voltage measurement of voltage, current, resistance using DC Potentiometer, measurement of inductance by Maxwell’s bridge, Hay’s bridge & Anderson’s and many more.
| ||
|
7.3.22 Network Lab | ||
|
This lab is well equipped with
variety of experimental kits & accessories. These are Norton Theorem,
Tellegin’s theorem, RL & R.C. Circuits, RLC Circuits, CRO, Millimeters and
Ammeters main experiments carried out by the students: Verification of super
position theorem, Norton theorem, Thevenin theorem & maximum power transfer
theorem. Image impendence & characteristics impendence of T and p
network, frequency response of twin – T notch kilter.
| ||
|
7.3.23
Electronics Lab. | ||
|
A well-established electronics lab
is available. A variety of instruments are installed in this lab required for
carry out the experiments. These are RC-couple BJT amplifier, RC-coupled FET
amplifier, Class-B push pull amplifier, wein-bridge oscillator, operation
amplifier kit (summer, difference and integrator), instrumentation amplifier and
emitter follower amplifier.
| ||
|
7.3.24
Energy Conversion Lab. | ||
|
This institute has setup an
advance energy conversion lab with variety of electrical machines. Laboratory
equipped with DC shunt motor, DC Series motor, induction motor and synchronous
motor. Major experiments performed by the students: - speed control of DC-shunt
motor, speed control DC series motor, speed control of synchronous motor and
characteristics of SCR and UJT.
| ||
7.3.25 Communication Lab. | ||
|
Communication lab of electronics
and communication engineering for third year students consists of a number of
trainer kits such as DSB/ASBAM transmitter, TDM pulse code modulator/Receiver,
FM transmitter of modulator/demodulator. Data formatting & carrier modulator
transmitter, carrier demodulation and data reformatting. CROs of 25 MHz,
function generation, AM/FM function pulse generator and demodulation kits etc
are available in the laboratory.
| ||
|
7.3.26 Analog Integrated Lab | ||
|
A well-established analog
integrated circuits lab is available. All instruments are of high quality and
accuracy. These are CROs, function generator multimeter, ammeter &
voltmeter, operational amplifier kits (inverting, non-inverting) PLL precision
rectifier, 555 timer betterworth active high pass and low pass filters, A/D
converter and D/A converter, DC regulated power supply. With the help of these
instruments students able to physically carry out the experiments prescribed in
the syllabus.
| ||
| 7.3.27 Microprocessor Lab | ||
|
This lab is well established with
multiple number of microprocessor kits 8085 and 8086 for carrying out
experiments of addition, substraction etc. using assemble language. Major
experiments performed in the lab: - Interfacing with 8255, interfering with
8253, verification of interrupts interfacing with ADC/DAC, serial communication
through RS-232IC etc.
| ||
| 7.3.28 Control System Lab. | ||
|
This lab is well established with
multiple numbers of electrical machines & accessories. DC potentiometer,
magnetic amplifier, universal motor, AC motor, CROs etc are available in the
laboratory. Major experiments performed by the students viz:- characteristics of
self exacted magnetic amplifier, series & parallel connected magnetic
amplifier, characteristics of synch torque transmitters, speed control of
universal motor using SCR and speed control of AC motor using TRAIC etc.
| ||
| 7.3.29 Machine Design Lab. | ||
|
Excellent faculty for training the
students on Systematic Methodologies, Creativity Analysis and Design of noval
mechanical devices.
| ||
| 7.3.30 Applied Thermodynamic Lab. | ||
|
Study of their lab for acquainting students to different types of thermodynamic processes. In addition the faculty to study the performance of Internal Combustion Engineers, Refrigeration and Air Conditioning etc. is fully developed.
| ||
| 7.3.31 Fluid Mechanics | ||
|
The lab is fully equipped for
importing exhaustive training to the students for solving fluid mechanics
problems and laying foundation for learning analytical, empirical and
experimental skills.
| ||
|
7.3.32
Heat And Mass Transfer Lab. | ||
|
This lab focuses on micro scale
and nanoscale processes, temperature control of electronics, high heat flux
engineering and connective transport.
| ||
| 7.3.33 Manufacturing Science Lab. | ||
|
The lab is equipped with various
experiments involving in manufacturing processes, metal forming, casting metal
removing and metal addition processes. The lab is equipped with
state-of-art-machines like lathe, shaper, drilling and welding processes.
| ||
|
7.3.34
Electric Machine Lab. | ||
|
The lab consists transformers,
D.C. Shunt generator and the experiments that are carried out in the section
are: Direct load test so fuid loss and efficiency of motors and generators.
Regenerative test or back-to-back sampler test to fuid efficiency of a
transformer by using two similar transformers. Speed control of D.C. Shunt motor
via field control & armature control.
| ||
|
RIT
houses a good library of its own which includes not only books linked with the
syllabus but it also approaches other areas so that the students get wider spectrum
of the world around. Faculty library is a proud member of DELNET which is a network
of libraries of AICTE approved Institutions. Library is also under the process
of computerization. RIT Library has also subscribed international journals in
the field of engineering and technology.
| ||
|
7.3.36 Machine Drawing
Lab. | ||
|
Machine drawing is indispensable
communicating language for mechanical engineers. This lab focuses students to
develop precision & sill for preparing machine drawing using I.S.O.
Students.
| ||
| 7.3.37 Mechanical Workshop | ||
|
A magnificent state-of-the-art workshop is
equipped with machine tools and gadgets of carpentry, foundry, fitting metal
joining and machine shop. Lathe and shaper machines, Gas Welding and Arc welding
set-ups are in the workshop. This workshop trains the students to deal with
various aspects of raw material, measurement and processes leading to its
conversion of raw material to usable product.
| ||
|
7.3.38 Dynamics of Machine Lab. | ||
|
The lab is established with latest modernized
equipment/instrument for comprehensive studies and experimentation on Velocity
of Acceleration, Governor, Gyroscope, Balancing, Clutch and Vibration etc.
| ||
|
7.3.39
Refrigeration
& Air Conditioning Lab. | ||
|
This lab is equipped for
experimentation studies on different types of refrigeration & air
conditioning systems with evaporators and extension devices etc. and prepares
the students for serving the industry.
| ||
|
7.3.40
Material Science & Testing Lab. | ||
|
The lab is fully equipped for experimentation
of comparative study of microstructures of welded components and different metal
specimens such as Cost Iron, Steel, Brass and Copper etc. Heat treatment
experiments of metals, study of corrosion and its effect. Lab also has the
testing machines for impact, fatigue, creep and harness testing of metals.
| ||
|
7.3.41
Measurement, Metrology & Control Lab. | ||
| The lab is fully developed for experimentation and studies on Stroboscope, Limits, Fits And Tolerances, Dial Indictor, Shark Plug, Tachometer, Sine Bar & Slip Gauges And Vibration Measuring Instrument to prepare the students befitting to serve the industry. | ||
|
|
| |
